Dataram DRI520P6 Instrukcja Użytkownika Strona 2
- Strona / 2
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
IBM P520
(Models E4A, M15, and M25)
• Shut down and unplug the system, then remove the cover.
• Remove air baffle and fans by lifting the 4 tabs and lifting the baffle
out of the system (See Figure 1).
Figure 1 Figure 2
• Each system has 8 memory module slots. The memory modules
should be installed in the order listed in your user guide.
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
g
rounded wrist stra
p
.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
g
rounded wrist stra
p
.
IBM P550
(Model M50 and E8A)
• Shut down and unplug the system, then remove the cover.
• Remove the system processor assembly by lifting the handles up
and pulling it out of the system, and place it on a static-free surface.
• Each processor assembly has 8 memory slots. The memory
modules should be installed in the order listed in your user guide.
• The numbering scheme is listed in Figure 1 below.
Figure 1 Figure 2
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
MEMORY INSTALLATION
MEMORY INSTALLATION
Note: Refer to your system owner’s manual for detailed instructions.
Note: Refer to your system owner’s manual for detailed instructions.
IBM P520
(Models E4A, M15, and M25)
• Shut down and unplug the system, then remove the cover.
• Remove air baffle and fans by lifting the 4 tabs and lifting the baffle
out of the system (See Figure 1).
Figure 1 Figure 2
• Each system has 8 memory module slots. The memory modules
should be installed in the order listed in your user guide.
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
g
rounded wrist stra
p
.
Caution: System parts are sensitive to electrostatic discharge and can be
damaged by the static charge you may carry. You should wear a
g
rounded wrist stra
p
.
IBM P550
(Model M50 and E8A)
• Shut down and unplug the system, then remove the cover.
• Remove the system processor assembly by lifting the handles up
and pulling it out of the system, and place it on a static-free surface.
• Each processor assembly has 8 memory slots. The memory
modules should be installed in the order listed in your user guide.
• The numbering scheme is listed in Figure 1 below.
Figure 1 Figure 2
• Remove the memory module fillers if present.
• Ensure that the connector locking tabs are in the unlocked position.
• Align the memory module notch with the key in the connector to
ensure that the module is installed properly and not damaged.
• Push the memory module firmly into the connector until the locking
tabs engage (See Figure 2).
• Replace the air baffle and put the cover back on.
1
2
Powiązane produkty i podręczniki dla Sprzęt komputerowy Dataram DRI520P6
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji